The short version
- Free founding pilot, for a limited number of municipalities: up to 15 culverts and 20 intersections, located, rated and photographed. Survey control set at cost.
- Proven field equipment: a Skadi® Gold GNSS receiver with the Skadi Smart Handle™ from Eos Positioning Systems, the Canadian GNSS maker.
- A QGIS map you own, with the source of every number shown, ready for your 588/17 review.
- After the pilot, your crew collects on patrol. We train, check and keep it current.
- May be eligible under your OCIF or Canada Community-Building Fund (gas tax) allocation. Your treasurer confirms. See ways to pay for it.
One map everyone can trust
Your consultant's drawings, the county GIS, the old road needs study and the developer's as-builts rarely line up. Nobody knows which one is right, and every new project pays someone to sort it out again.
The fix: we set a small network of survey points the municipality owns, check them twice, line the public mapping up to them, then prove it on 35 points we didn't use.
Built on public LiDAR the province already paid for. No new flying and no new base mapping. A small number of survey points, spread across the whole municipality and each provincial LiDAR dataset, lines that mapping up everywhere.
It gets better as your crew works. Every RTK point your staff collect is another check on the fit, and where the points show a local pattern, we tighten the mapping there.

What you get
- A desktop GIS map of your roads, ditches and drainage, delivered as a QGIS project you own, in your municipality's coordinate system (UTM or MTM) and height datum (CGVD2013 or CGVD28), with a metadata record for every layer: source, date, accuracy and licence.
- Field-verified culverts, starting with a pilot sample: each one visited is located by RTK GNSS, condition-rated and photographed. The rest are mapped from public data as candidate crossings and flagged until someone gets to them.
- Every value tagged by source: measured by us, collected by your staff, municipality-supplied, or missing. You can see what's solid and what still needs a look.
- Survey control points the municipality owns, set and observed by us, tied to NAD83(CSRS) and CGVD2013, with coordinates also given in your municipality's own system and older CGVD28 heights where your drawings use them. Your old data, your contractors and future work all sit on the same ground. Crews can check into them, or set up a base on them for RTK work.
- A check on the public data you rely on: we measure how far the public LiDAR and imagery sit from our control points in your municipality. Where the difference is consistent, we line it up to the control and report what's left. Where it isn't, we report it as found.
- A storm capacity flag on every crossing visited: a screening check of whether the measured pipe is big enough, for your engineer to confirm. Crossings not yet visited carry the pipe size they would need.

How a pilot works
- A call to set up a meeting about where your plan stands and which roads matter most.
- Sites spread across the whole municipality: up to 15 road culverts, 20 road intersections and 20 open-sky control points, agreed with your public works staff.
- Fieldwork from the shoulder and ditch, with traffic protection to OTM Book 7 and utility locates where needed.
- Delivery: the pilot data in open formats that open in free QGIS, one record sheet per culvert with its storm capacity flag, a control point register, a public data accuracy note, and a one-page summary for Council.
Free pilots are offered to our first few municipalities while we prove the process and build case studies. After that, engagements are paid work. The culvert and intersection work in a pilot, including the storm capacity flags, is offered at no cost to the municipality, for up to 15 culverts and 20 intersections. More can be added as paid work. Survey control, up to 20 points, is set at cost: the municipality supplies the materials, and we set and observe the points at cost. The full municipal QGIS project, drainage screening and ongoing upkeep are paid work. We also ask for written permission to work in the road allowance, any culvert or road records you already hold, one staff contact, and permission to share the results as a case study. There is no obligation to buy anything after the pilot, and nothing is published without your OK.
Culverts are rated once snow and ice are off the ends, so winter is for planning and picking sites, and culvert fieldwork starts after spring runoff, in time for results to feed your July 1 progress review.
After the pilot: your crew collects, we check
- We train your staff on the pilot sites, so everyone rates culverts the same way.
- Your crew logs culverts during regular patrols and ditch and culvert work, with a GNSS receiver arranged through us and pick-list forms in free QField on a phone. Records come back by cable or file transfer, with no cloud subscription needed. No separate project, no extra trips.
- Every record is checked before it goes into your map, and tagged as collected by your staff.
- We keep the map and the control current: the QGIS project, your 588/17 numbers, and the survey control points, which we set and observe ourselves.
- Need it done faster? We can do the extra sites as paid work.
How the work is done
- Culvert condition is rated on the five-point scale Ontario asset management plans use, Very Good to Very Poor. Each rating comes with what we saw at the inlet, outlet, barrel and road above, how blocked it is, photos, and a recommended action: monitor, clean out, repair or replace, with timing. Structures 3 m and over stay with your bridge inspection engineer, and we flag any we find for OSIM.
- Every position comes with its measured accuracy. Typical RTK is a few centimetres.
- Checked every day. RTK corrections stream from a nearby base station, and every field day starts and ends with a check on published provincial survey control. If the check fails, no data is collected that day.
- Every number can be traced back. Every record carries its fix, accuracy, time, collector and that day's control check.
- Nothing is dug or cleaned. Buried or flooded inverts are measured down from the top of the pipe and marked as measured, derived or estimated, with sediment depth recorded.
- Proven field equipment. Fieldwork uses a Skadi® Gold GNSS receiver with the Skadi Smart Handle™ from Eos Positioning Systems, the Canadian GNSS maker trusted by municipal and utility crews around the world.
- Built to feed what you already have: your asset management plan, your consultant's work and your county or regional GIS. It replaces none of them.
Technical notes for your engineer or GIS tech
- Control is checked twice. Each point is observed by RTK with raw data logged, then checked by post-processing. Final coordinates are published with their accuracy, point by point.
- Independent check. Only the control points are used to line up the public mapping. The culvert and intersection points are held back, and the fit at each one is reported.
- How the public LiDAR is lined up. Control is placed on both sides wherever two provincial LiDAR datasets meet, so one shift is never applied across two. Some points are always held back from the fit so the check stays independent. A shift corrects offset, not distortion within a dataset, and the fit is reported at every check point.
- Collected in Canada's national frame, delivered in yours. We collect in NAD83(CSRS) and CGVD2013 and deliver in your coordinate system and height datum, with the conversion documented.
- Control records load straight into your GIS, as open GeoPackage and CSV files, with the datum transformation documented.
- Ready for Canada's new reference system. Every point is tied to published provincial survey control and recorded with its datum, epoch and geoid model, so your data converts cleanly when Canada moves from NAD83(CSRS) to its new national reference system.
Why it fits a small municipality
- Open-source QGIS, so no licence fees.
- The data stays the municipality's. Open formats, and no software subscription.
- Ready for your annual progress review, due each July 1 under O. Reg. 588/17.
- Supports your infrastructure funding. OCIF and your federal gas tax allocation both expect a current 588/17 asset management plan, and better condition and risk data strengthens it. Field-checked, risk-ranked crossings also make stronger applications for programs like climate resilience funding.
Ways to pay for it
- OCIF (Ontario Community Infrastructure Fund). Formula funding your municipality already receives each year, with no application and a guaranteed yearly minimum. Third-party condition assessments and consultant work on asset management planning are eligible costs, and allocations can be banked for up to five years.
- Canada Community-Building Fund (federal gas tax). Your annual allocation can go to capacity building, which covers asset management studies, systems, software, third-party assessments and training, as well as capital work on roads, bridges and stormwater.
- Rural Ontario Development Program. Provincial cost-share for rural municipalities, with the next intake open January 25 to March 4, 2027. The Strategies and Plans stream covers up to 50% of eligible costs, and professional fees, including surveys and consulting, are eligible. It can't be combined with other provincial funding for the same project, and the province decides which projects qualify.
- We do the groundwork for your application: scope, site counts, maps and the condition data your write-up needs. Your finance staff confirm eligibility against your own funding agreements.
Limits
Visual condition ratings, screening-level capacity flags and RTK positions with centimetre-level measured accuracy only. Not a structural assessment, hydraulic design or engineering assessment, and not a legal survey: nothing here marks or defines a property line.
Status
Now taking a small number of founding pilot municipalities in Ontario, starting in Eastern Ontario. Once those spots are filled, engagements move to paid work.
Call to set up a meeting with Trevor
Tell us where you are with the plan. Or call or text 613-219-0288, or email founder@tdoubleai.ca.
Trevor Affleck, A.Sc.T. 25+ years in Ontario construction layout, legal surveys and municipal infrastructure mapping.